View M150X3-T05_1268947.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
- CONTENTS REVISION HISTORY 1. GENERAL DESCRIPTION
1.1 OVERVIEW 1.2 FEATURES 1.3 APPLICATION 1.4 GENERAL SPECIFICATIONS 1.5 MECHANICAL SPECIFICATIONS -------------------------------------------------------------------------------------------------------------
3 4
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE 2.2.2 BACKLIGHT UNIT
-------------------------------------------------------
5
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE 3.2 BACKLIGHT UNIT
-------------------------------------------------------
7
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE 4.2 BACKLIGHT UNIT
-------------------------------------------------------
10
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 COLOR DATA INPUT ASSIGNMENT
-------------------------------------------------------
11
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE
-------------------------------------------------------
14
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS
-------------------------------------------------------
17
8. PRECAUTIONS
8.1 HANDLING PRECAUTIONS 8.2 STORAGE PRECAUTIONS 8.3 OPERATION PRECAUTIONS
-------------------------------------------------------
20
9. PACKAGING
9.1 PACKING SPECIFICATIONS 9.2 PACKING METHOD
-------------------------------------------------------
21
10. INCOMING INSPECITION DAY 11. DEFINITION OF SHIPPING LABEL ON MODULE
-------------------------------------------------------------------------------------------------------------
23 24
2 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
REVISION HISTORY
Version Date Page (New) All 17 24 Section All 7.2 11.1 Issue Approval Specification. Center Luminance of White 200(Min.)/250(Typ.) 240(Min.)/300(Typ.). Delete (c) Color Filter:0->CMO,2->Toppan. Description
Ver 2.0 July.23'2001 Ver 2.1 Mar.01'2002
3 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
M150X3-T05 is a 15.0" TFT Liquid Crystal Display module with 4 CCFL Backlight units and 60 pins TTL interface. This module supports 1024 x 768 XGA mode and can display 262,144. The optimum viewing angle is at 6 o'clock direction. The inverter module for Backlight is not built in.
1.2 FEATURES
- XGA (1024 x 768 pixels) resolution - DE (Data Enable) only mode -TTL Interface with 2pixels/clock
1.3 APPLICATION
- Desktop monitors
1.4 GENERAL SPECIFICATI0NS
Item Active Area Bezel Opening Area Driver Element Pixel Number Pixel Pitch Pixel Arrangement Display Colors Transmissive Mode Specification 304.1(H) x 228.1(V) (15.0" diagonal) 308.2(H) x 232.1(V) a-Si TFT active matrix 1024 x R.G.B. x 768 0.297(H) x 0.297(W) RGB vertical stripe 262,144 Normally white Unit mm mm pixel mm color Note (1) -
1.5 MECHANICAL SPECIFICATIONS
Item Horizontal(H) Module Size Vertical(V) Depth(D) Weight Min. Typ. 331.6 254.76 13.0 Max. 1,350 Unit mm mm mm g Note (1) (1)(2) -
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions. Note (2) The depth is without connector and boss.0
4 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Storage Temperature Operating Ambient Temperature Storage Humidity Operation Humidity Shock (Non-Operating) Vibration (Non-Operating) (a) 85 %RH Max. (Ta 40 C). (b) Wet-bulb temperature should be 39 C Max. (Ta > 40 C). (c) No condensation of water. Symbol TST TOP HST HOP SNOP VNOP Value Min. -20 0 5 20 Max. +60 +50 85 85 50 2 Unit C C % % G G Note (1) (1), (2) (3), (5) (4), (5)
Note (1) Temperature and relative humidity range is shown in the figure below.
Relative Humidity (%RH)
100 85 80
60
Operating Range
40
20 5 -40 -20 0
Storage Range
20 40 60 80
Temperature (C)
Note (2) The temperature of panel surface should be 0 C Min. and 60 C Max. Note (3) 6ms, 1 time each X,Y and Z directions Note (4) 10 ~ 500 Hz, 1 cycle/20min. 1.5mm max, 1 hour each X, Y and Z directions Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture.
5 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE
Item Power Supply Voltage Symbol VDD Value Min. -0.3 Max. 4.0 Unit V Note
2.2.2 BACKLIGHT UNIT
Item Lamp Voltage Lamp Current Lamp Frequency Symbol VL IL FL Value Min. 522 2.0 30 Max. 675 7 80 Unit VRMS mARMS KHz Note (1), (2), IL = 6 mA (1), (2)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to Section 3.2 for further information).
6 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
Parameter Power Supply Voltage Rush Current Power Supply Current Input voltage White Black Vertical Stripe "H" Level "L" Level Symbol VDD IRUSH lcc VIH VIL Min. 3.0 2.4 0 Value Typ. 3.3 350 530 450 Max. 3.6 1.5 3.6 0.9 Unit V A mA mA mA V V Note (2) (3)a (3)b (3)c -
Note (1) The module should be always operated within above ranges. Note (2) Measurement Conditions:
+3.3V Q1 2SK1475 VDD FUSE R1 47K C3 (LCD Module Input) 1uF
(High to Low) (Control Signal) R2 SW 1K +12V 47K
Q2 2SK1470
VR1 C1
C2
0.01uF 1uF
+3.3V
0.9 0.1
VDD
VDD 470s
GND
7 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Note (3) The specified power supply current is under the conditions at VDD =3.3V, Ta = 25 2 C, DC Current and fv = 60 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern
Active Area c. Vertical Stripe Pattern
Active Area
RGBRGB BRGBRGBR BRGBRGBR RGBRGB
Active Area
3.2 BACKLIGHT UNIT
Parameter Lamp Input Voltage Lamp Current Lamp Turn On Voltage Operating Frequency Lamp Life Time Power Consumption Symbol VL IL VS FL LBL PL Min. 552 2.0 30 40,000 Value Typ. 614 6 45 50,000 14,740 Max. 675 7 o 870 (25 C) o 1,090 (0 C) 80 Unit VRMS mARMS VRMS VRMS KHz Hrs mW
Ta = 25 2 C Note IL = 6 mA (1) (2) (2) (3) (5) (4), IL = 6 mA
Note (1) Lamp current is measured by utilizing a high frequency current meter as shown below: HV (Pink/ Blue) 1 2
LCD Module
LV (White/ Black)
Inverter
A Current Meter
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise the lamp may not be turned on.
8 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Note (3) The lamp frequency may generate interference with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (4) PL = IL X VL Note (5) The lifetime of lamp is defined as the time when it continues to operate under the conditions at Ta = 25 2 C and IL =6.0mARMS until one of the following events occurs: (a) When the brightness becomes 50% of its original value. (b) When the effective ignition length becomes 80% of its original value. (Effective ignition length is defined as an area that the brightness is less than 70% compared to the center point.) Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. The performance of the Backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for the lamp. All the parameters of an inverter should be carefully designed to avoid generating too much current leakage from high voltage output of the inverter. When designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument.
o
9 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
SCAN DRIVER IC
SIGNAL
TTL INPUT / TIMING CONTROLLER
TFT LCD PANEL (1024x3x768)
INPUT CONNECTOR
(Molex 52760-0600)
DATA DRIVER IC
VDD
VDD
DC/DC CONVERTER & REFERENCE VOLTAGE GENERATOR
LAMP CONNECTOR (JST-BHSR-02VS-1)
BACKLIGHT UNIT
4.2 BACKLIGHT UNIT
1 HV (Pink) 2 LV (White) 1 HV (Blue) 2 LV (Black)
1 2 1 2
HV (Pink) LV (White) HV (Blue) LV (Black)
10 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Symbol GND RO0 RO1 RO2 RO3 RO4 RO5 GND GO0 GO1 GO2 GO3 GO4 GO5 GND BO0 BO1 BO2 BO3 BO4 BO5 GND RE0 RE1 RE2 RE3 RE4 RE5 GND GE0 I/O I I I I I I I I I I I I I I I I I I I I I I I I I Function Ground Red odd data 0 Red odd data 1 Red odd data 2 Red odd data 3 Red odd data 4 Red odd data 5 Ground Green odd data 0 Green odd data 1 Green odd data 2 Green odd data 3 Green odd data 4 Green odd data 5 Ground Blue odd data 0 Blue odd data 1 Blue odd data 2 Blue odd data 3 Blue odd data 4 Blue odd data 5 Ground Red even data 0 Red even data 1 Red even data 2 Red even data 3 Red even data 4 Red even data 5 Ground Green even data 0 Pin No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Symbol GE1 GE2 GE3 GE4 GE5 GND BE0 BE1 BE2 BE3 BE4 BE5 GND PULL PULL ENAB GND GND DCLK GND GND NC NC GND GND GND VDD VDD VDD VDD I/O I I I I I I I I I I I I I I I Function Green even data 1 Green even data 2 Green even data 3 Green even data 4 Green even data 5 Ground Blue even data 0 Blue even data 1 Blue even data 2 Blue even data 3 Blue even data 4 Blue even data 5 Ground Must be fixed to 0 V Must be fixed to 0 V Data enable signal Ground Ground Dot clock signal Ground Ground Must be floating Must be floating Ground Ground Ground +3.3V Power supply +3.3V Power supply +3.3V Power supply +3.3V Power supply
Connector Part No.: 52760-0600(Molex) User's connector Part No: 53475-0600(Molex)
11 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Correspondence between Data and Display Position
S0001 S0002 S0003 S0004 S0005 S0006 S0007 S0008 GE RE BO GO RO BE GE RE 0001 0001 0001 0002 0002 0002 0003 0003 S3071 S3072 BO GO 1024 1024
C001
C768
RE 0001
GE 0001
BE 0001
RO 0002
GO 0002
BO 0002
RE 0003
GE 0003
GO 1024
BO 1024
5.2 BACKLIGHT UNIT
Pin 1 2 Symbol HV1 LV Description High Voltage Ground Color Pink/ Blue White/ Black
Note (1) Connector Part No.: BHSR-02VS-1
(JST) or equivalent
Note (2) Matching Connector Part No.: SM02B-BHS-1-TB (JST) or equivalent
12 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
5.3 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input the brighter the color. The table below provides the assignment of color versus data input. Data Signal Green
R1 R0 G5 G4 G3 G2 G1 G0 B5 B4
Color
R5 R4
Red
R3 R2
Blue
B3 B2 B1 B0
Black Red Green Basic Blue Colors Cyan Magenta Yellow White Red(0) / Dark Red(1) Red(2) Gray : Scale : Of Red(61) Red Red(62) Red(63) Green(0) / Dark Green(1) Green(2) Gray : Scale : Of Green(61) Green Green(62) Green(63) Blue(0) / Dark Blue(1) Blue(2) Gray : Scale : Of Blue(61) Blue Blue(62) Blue(63)
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1
Note (1) 0: Low Level Voltage, 1: High Level Voltage
13 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram. Parameter Symbol Pixel clock Frequency Fck Pixel clock period Tck Duty ratio (%Tch) High time Tckh Low time Tckl DATA Setup time Tsd Hold time Thd DE Setup time Tsde Hold time Thde Vertical Vertical Frequency Fv Signal Vertical display active period Tvda Vertical display blank period Tvdb Vertical period Tvp Horizontal Horizontal display active Thda Signal period Horizontal display blank period Thdb Horizontal period Thp Signal DCLK Min 25 45 5 5 4 4 4 4 768 1 769 512 38 550 Typ 32.5 30 50 60 768 38 806 512 160 672 Max 40 40 55 75 768 512 388 900 Unit MHz ns % ns ns ns ns ns ns Hz Thp Thp Thp Tck Tck Tck Remarks
Tch/Tck
Note (1) Because this module is operated by DE only mode, Hsync and Vsync input signals should be set to low logic level or ground. Otherwise, this module would operate abnormally.
14 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
INPUT SIGNAL TIMING DIAGRAM
Tvp Tvdb Tvda
DE
768
1
2
768
Thp Thdb DE DCLK Thda
DATA
Valid display data ( 512 Tck)
Invalid
Valid
Tck Tckh Tckl Tch
0.7VDD 0.5VDD 0.3VDD
DCLK Tsd DATA Thd
0.7VDD 0.3VDD
Tsde DE
Thde
0.7VDD
15 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
6.2 POWER ON/OFF SEQUENCE
Power On
90%
Power Off
90% 10%
Restart
t4 10%
- Power Supply for LCD, VDD
0V
10% t1 t2 t3
- Interface Signal (LVDS Signal of Transmitter), VI
0V
t5
Valid Data
t6
- Power for Lamp Timing Specifications: 0 < t1 10 msec 0 < t2 50 msec 0 < t3 50 msec t4 1 sec t5 100 mesc t6 100 msec
OFF
ON
OFF
Note (1) Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD VDD to 0 V. Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight inverter power must be turned off before the power supply for the logic and the interface signal is invalid.
16 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Inverter Current Symbol Value Unit o Ta C 252 Ha %RH 5010 VDD 3.3 V According to typical value in "3. ELECTRICAL CHARACTERISTICS" IL 6.0 mA
The measurement methods of optical characteristics are shown in Section 7.2. The following items should be measured under the test conditions described in Section 7.1 and stable environment shown in Note (4).
7.2 OPTICAL SPECIFICATIONS
Item Contrast Ratio Response Time Center Luminance of White Red Color Chromaticity Green Blue White Horizontal Viewing Angle Vertical Symbol CR TR TF L Rx Ry Gx Gy Bx By Wx Wy x+ xY+ YCondition Min. 250 240 0.607 0.323 0.272 0.558 0.111 0.064 0.280 0.300 50 50 30 50 Typ. 300 7 23 300 0.637 0.353 0.302 0.588 0.141 0.094 0.310 0.330 60 60 40 60 Max. 22 38 0.667 0.383 0.332 0.618 0.171 0.124 0.340 0.360 Unit ms ms 2 cd/m Deg. Note (2), (4) (3) (4)
x=0, Y =0 Viewing Normal Angle
(1), (4)
CR10
17 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Note (1) Definition of Viewing Angle (x, y): Normal x = y = 0 yX- = 90 xxx+ y+ y+ 12 o'clock direction y+ = 90
6 o'clock y- = 90
y-
x+
X+ = 90
Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (5). Note (3) Definition of Response Time (TR, TF):
Gray Level 63
100% 90%
Gray Level 63
Optical Response Gray Level 0
10% 0%
Time TR TF
18 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Note (4) Measurement Setup: The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.
LCD Module LCD Panel Center of the Screen Photometer (TOPCON BM-5A)
Field of View = 2
Light Shield Room (Ambient Luminance < 2 lux)
500 mm
Note (5)
Definition of luminance measured points:
Horizontal Line Number
0 0 256 512 768 1023
Vertical Line Number
192
1
2 X : test point
384
5
X=1 to 5
576 3 4
767
Active area
Horizontal Line Number [pixel]
19 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
8. PRECAUTIONS
8.1 HANDLING PRECAUTIONS
(1) The module should be assembled into the system firmly by using every mounting hole. Be careful not to twist or bend the module. (2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause electrical short or damage the polarizer. (3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and assembly process. (4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer is very soft and easily scratched. (5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not use Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might permanently damage the polarizer due to chemical reaction. (6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel for a long time. (7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap. (8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC. (9) Do not disassemble the module. (10) Do not pull or fold the lamp wire. (11) Pins of I/F connector should not be touched directly with bare hands.
8.2 STORAGE PRECAUTIONS
(1) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. (2) It is dangerous that moisture come into or contacted the LCD module, because the moisture may damage LCD module when it is operating. (3) It may reduce the display quality if the ambient temperature is lower than 10 C. For example, the response time will become slowly, and the starting voltage of lamp will be higher than the room temperature.
8.3 OPERATION PRECAUTIONS
(1) Do not pull the I/F connector in or out while the module is operating. (2) Always follow the correct power on/off sequence when LCD module is connecting and operating. This can prevent the CMOS LSI chips from damage during latch-up. (3) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.
20 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 5 LCD modules / 1 Box (2) Box dimensions : 353(L) X 268(W) X 462(H) mm (3) Weight : approximately 8.5Kg ( 5 modules per box)
9.2 PACKING Method
Figures 9-1and 9-2 are the packing method.
Figure. 9-1 Packing method
21 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
Figure. 9-2 Packing method
22 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
10. INCOMING INSPECTION DAY
The Supplier should be acquainted the inspection results (acceptance or rejection) by Customer, and the results are in accordance with the incoming inspection standard within 30 days after the date of the bills of lading. Should Customer fail to so notify the Supplier within the said 30 days period. The Customer's right to reject the LCMS shall then lapse, and the said LCMS shall be deemed to have been accepted by the customer.
23 / 24
Version 2.1
Issued Date:Mar.01'2002 Model No.: M150X3-T05
Approval
11. DEFINITION OF LABELS
11.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. M150X3 -T05 Rev. XX
MADE IN TAIWAN
CHI MEI
OPTOELECTRONICS
XXXXXXXYMDLNNNN
E207943
MADE IN TAIWAN
(a) Model Name: M150X3 -T05 (b) Revision: Rev. XX, for example: C1, C2 ...etc. (c) Serial ID: X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date
CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below: (a) Manufactured Date: Year: 1~9, for 2000~2009 Month: 1~9, A~C, for Jan. ~ Dec. Day: 1~9, A~Y, for 1 to 31 , exclude I and O (b) Revision Code: cover all the change (c) Serial No.: Manufacturing sequence of product (d) Product Line: 1 -> Line1, 2 -> Line 2, ...etc.
st st
24 / 24
Version 2.1
HIGH VOLTAGE CAUTION

▲Up To Search▲

Price & Availability of M150X3-T05

	To Download M150X3-T05 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .